How to Install a Ghost Immobiliser
A ghost immobiliser is a hidden security system that protects your car from hacking and key cloning. It works by stopping the engine from running unless it is started using a PIN code that can be up to 20 characters long.
This additional layer of security is not visible to thieves who might not be aware of it. Some systems have an app which allows the owner to deactivate their immobiliser in the event of forgetting their PIN or use the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser, a cutting edge security system, can be integrated directly into the ECU of your vehicle. It is a subtle security barrier against thieves. It is highly efficient and user-friendly. This makes it a valuable addition to your vehicle's arsenal of security. But, as with any other anti-theft device, it's not foolproof and requires regular maintenance to ensure proper operation. Luckily, this guide will assist you in getting the most out of your Ghost 2 Immobiliser.
CAN (Controller Area Network) is a reliable serial network that lets microcontrollers communicate with each other in short distances, without the necessity of central control units. It is designed to multiplex electrical wiring in vehicles, which saves on copper. It offers many advantages, such as low cost and simple use.
The CAN protocol is used in most modern vehicles to communicate with the engine management system, transmission controller, steering control module air conditioning controls and many more. It also carries sensor data like speed sensors and inputs, to control different features of the vehicle. The CAN bus is used to monitor these diverse components, and it can stop the car from starting if they are in an unsafe state.
It is important to understand how the CAN bus functions and how it's secured. The CAN bus is an excellent method to enhance the features of your vehicle, but it's essential to protect it from hackers and other threats. The best way to do this is by installing firewalls and monitoring your CAN bus through software.
Ghost2's control device is hidden within the car's dashboard or wiring harness, which prevents a thief from physically tampering it. It's also impossible to reset the PIN code or emergency code without access to the vehicle.
If you need to hand over your vehicle to a valet parking service, maintenance, or any other reason, you can turn on the Transport Mode. This feature turns off both the keyfob as well as the ignition functions of the Ghost immobiliser. It will only be activated when the vehicle has reached 31 mph for a period of 15 minutes.
Making PIN codes
The Ghost immobiliser shields your vehicle from theft. The most advanced technology utilizes an PIN code to shut down the engine and block it from starting if you do not have the correct code or a valid fob/mobile device. Its discreet design ensures that the system is unnoticeable and offers unbeatable protection against theft. Moreover the system is TASSA verified and can lead to significant savings on car insurance premiums.
During the installation when you install the Ghost system goes into an learning mode that records the sequence of buttons pressed to generate your unique pin code. The installer will guide you through activating the system after the pin code is created. Once activated by the system, the Ghost system will disable the motor that starts your vehicle until a valid pin code is entered or the vehicle is switched to transport mode. This makes it extremely difficult for thieves to copy or hack into your vehicle's start system.
It is simple to install it is easy to install a Ghost immobiliser, but you must follow the specific instructions included in the user guide to ensure the proper operation. Hand tools are essential in making precise connections and a multimeter can aid in checking the electrical value. Insulation tape, heat shrink tubing, and cable ties can be utilized to shield wires from damage. Also, make sure to check the system on a regular basis to find any potential issues and errors.
It is crucial to test the system one last time before turning on the ignition. The Ghost immobiliser will be able to rearm itself after a period of 3 to 30 seconds, depending on your car's model. The system also comes with a Service/Valet Mode that allows you to temporarily disable the system to service or valet parking.
Ideally, the immobiliser should be placed in a discreet location beneath the dashboard or steering wheel. It is recommended to use a small amount of duct tape or paint to mark the CAN H and CAN L wires to ensure that you easily locate them during testing. In addition the CAN H and CAN L wires should be connected to a power source that is able to provide continuous 12V. It is also essential to re-check the connections after testing, since misidentifying these wires can cause the system to malfunction.
Invoking the system
A ghost immobiliser prevents your vehicle from starting until you press a sequence of buttons within the car typically the steering wheel, door panel, or central console. The sequence can be changed by the user in case it is needed. Once activated, the system will not be deactivated. This is a fantastic option for those who want to safeguard their vehicle against theft.
The system is designed to be undetectable, which means it cannot be detected by modern diagnostic tools or code-grabbing technology. It also doesn't broadcast radio signals which makes it difficult for thieves to identify the device.
If the device is located, it will stop the engine from running. It will also sound an alarm to scare thieves away. The device can be used to track the location of a vehicle which can help police recover the vehicle if it has been taken.
If you're interested in a ghost immobiliser, contact the experts at Car Specalist Customs to get a quote and discuss your options. We are able to install ghost immobilisers in your vehicle. We will ensure that it is concealed in a place that is difficult to access. We can also install additional security measures, such as the kill switch and wheel lock to ensure your vehicle is secure from thieves.
Disarming the system
It is essential to know how to deactivate the Ghost immobiliser if installed in your vehicle. It can be used in case you forget your keys or the battery in your car dies. The system uses an unique PIN code, which only you are aware of. It cannot start the car without this code. Pressing a combination button on the dashboard or steering wheel is the easiest method of entering your code. This is a lot easier than using a key fob, and stops others from copying your remote.
Unlike some aftermarket immobilisers that require cutting wires to install, Ghost2 is non-invasive and works with your vehicle's CAN bus network to operate. Its most distinctive characteristic is that it disables the engine, without affecting normal functions of the vehicle. This makes it extremely difficult for thieves to use signal boosts or to clone keys for cars. Additionally, it doesn't emit radio frequencies, so thieves aren't able to detect the system.
The Ghost system comes with the option of a Transport Mode which allows you to temporarily disable security for situations such as transportation or service. This feature is great for when you're loaning your vehicle out to someone else without sharing your PIN code or if your vehicle needs to be secured while you drive it. Press the button five times within two seconds to enable Transport Mode. The Ghost system will confirm activation by 5 indication signals.
Save the emergency code in your vehicle in a secure location. Then, if you ever discover yourself locked out of your vehicle, you can contact the technician or company that installed the system and they will give you the code. If you are unable to reach them You can always try contacting an authorized dealer but this would require verification procedures and could incur additional fees.
This system is not only practical, but it can also safeguard your vehicle from theft, and also reduce the cost of insurance. Many insurance companies offer lower rates or financial incentives to install this system to prevent theft.